Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

  • opjose's Avatar
    Yesterday, 10:27 AM
    It is also illegal in other states. Colorado and a few others now have laws on the books, while many other states are also drafting legislation. ...
    15 replies | 212 view(s)
  • opjose's Avatar
    04-18-2014, 02:39 PM
    Are you trying to find out what you are getting in Realflight? If so FPS is in the navguide. Edit the displayed widget list via the menu to...
    1 replies | 88 view(s)
  • opjose's Avatar
    04-18-2014, 01:37 PM
    331 replies | 35174 view(s)
  • opjose's Avatar
    04-18-2014, 01:34 PM
    70oz servos for all surfaces and 80oz or so for the rudder is MORE than sufficient on this plane. I've flown mine with inexpensive digital 133oz...
    4 replies | 131 view(s)
  • opjose's Avatar
    04-18-2014, 01:27 PM
    Jester has quite extensive experience. He may not have your particular plane, but he is experienced with using MUCH BETTER hardware than what you...
    15 replies | 212 view(s)
  • opjose's Avatar
    04-18-2014, 01:21 PM
    opjose replied to a thread 72 MHz or 2.4 in Beginners
    Who makes the receivers? If you can find a transmitter with the same frequency the receivers use and the SAME "SHIFT" pattern, you may be able to...
    55 replies | 1110 view(s)
  • opjose's Avatar
    04-08-2014, 11:36 AM
    Glow silicon lines seem to hold up fine. The problem is with glow fuel corroding the metal fittings, brass, etc. over time. Enough builds up to...
    15 replies | 354 view(s)
  • opjose's Avatar
    04-08-2014, 11:30 AM
    I haven't done it on the smaller Stiks such as yours. However on the larger Stiks, I find that setting the inner "flaps" as secondary ailerons...
    3 replies | 92 view(s)
  • opjose's Avatar
    04-02-2014, 11:14 AM
    opjose replied to a thread giant stik in ARF or RTF
    You should seriously consider increasing the capacity of the flight pack. At worst put in two 6V 2500 NiMH packs and connect them in parallel to...
    18 replies | 291 view(s)
  • opjose's Avatar
    04-01-2014, 02:47 PM
    opjose replied to a thread giant stik in ARF or RTF
    What engine mounts are you going to use? The ones that came with the plane? Yes you can do as you said to hold the weights on. Remember though...
    18 replies | 291 view(s)
  • opjose's Avatar
    04-01-2014, 10:15 AM
    opjose replied to a thread giant stik in ARF or RTF
    Yup you can do what Tom suggests. That will work well. You can also build a NEW "box" if you choose. Just make sure you use relatively thick...
    18 replies | 291 view(s)
  • opjose's Avatar
    03-31-2014, 11:12 AM
    opjose replied to a thread giant stik in ARF or RTF
    Been there, tried that, found it problematic. Avoid wooden dowels. There is not enough contact area nor anti-flex strength to avoid the torsion...
    18 replies | 291 view(s)
  • opjose's Avatar
    03-31-2014, 10:59 AM
    opjose replied to a thread giant stik in ARF or RTF
    I've built 11 of these planes used as club trainers... Don't use dowels. There will be too much torque on the dowels and the extra length produces...
    18 replies | 291 view(s)
  • opjose's Avatar
    03-31-2014, 10:38 AM
    I've seen no problems as well... however I redefined all of my plane setups after the upgrade. Wasn't there some discussion on another thread or...
    284 replies | 11984 view(s)
  • opjose's Avatar
    03-25-2014, 03:32 PM
    Yup. Good upgrade! From the Upgrade notes: New Features & Improvements Added LCD contrast calibration on the Raw I/O screen. If your...
    284 replies | 11984 view(s)
No More Results
About min$2crash

Basic Information

About min$2crash
Location:
Idaho, MI

Statistics


Total Posts
Total Posts
174
Posts Per Day
0.09
General Information
Last Activity
04-02-2014 01:42 PM
Join Date
02-15-2009
Referrals
0
All times are GMT -6. The time now is 03:27 AM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.