T-one models F22A Raptor scale build!!!
#1
Thread Starter
My Feedback: (9)
T-one models F22A Raptor scale build!!!
Well it’s finaly time to get building on my all time favorite plane! T1 really did this one right! This one I got is unpainted so I can add my own scheme and details for scale compitition.
The production models will will be the same as this other then the panel lines will be fixed and not so pronounced. I will fix that myself on this one. As far as the build goes I want to keep it as stock as possible but I’m sure I’ll add my own spin on certain parts just to be more scale.
Going to power it with a kingtech 260.
I really like how the bomb doors are done. The hinging and doors
line up perfect. Same with the gear doors. The gear is amazing looking. Will post more pics of the in a few days.
The production models will will be the same as this other then the panel lines will be fixed and not so pronounced. I will fix that myself on this one. As far as the build goes I want to keep it as stock as possible but I’m sure I’ll add my own spin on certain parts just to be more scale.
Going to power it with a kingtech 260.
I really like how the bomb doors are done. The hinging and doors
line up perfect. Same with the gear doors. The gear is amazing looking. Will post more pics of the in a few days.
#4
Looks like the Kracken has been released!! Let the fun begin!!! Hiep Custom Pipes has shipped your pipe today that should be a drop in fit. The quality of Hiep pipes is what this F-22 needs for optimum performance with a KingTech K-260 blowing down its throat. The T-One Models quality is absolutely second to none as you will see as Kris posts his pictures.
Dirk
Pacific RC Jets
Dirk
Pacific RC Jets
Last edited by flejter1; 01-31-2019 at 06:58 PM.
#11
Thread Starter
My Feedback: (9)
Aircraft is available in twin or single configuration. I would say twin K120s up too twin K160s. For single I would say K210 if built light up to a K320. I will have more input on the recommended single engine size after flying it. I really don't see any need to have anything bigger then a K260 even with the vectoring. During testing they flew this airframe on a single K160 with just a straight pipe but that was a bare airframe.
#13
Thread Starter
My Feedback: (9)
This plane has the formation lights and nav lights installed already so that a big plus. Lighting kit looks very nice with its own controller. The F22 does not have many lights only the nav/ strobes on the wingtips and formation light and landing lights. I do plan on adding lights to the cockpit myself but that will wait until after Florida Jets. Also want to add a moving pilot with a robot controller but it also might have to wait until after the first event.
Will be working with Sean McHale with Strictly Scale to get some super scale missiles to install in the weapons bay. I really like how T-1 added detail already in the weapons bay. Should make it allot easier to finish that part off. The bottom doors are very cool how they open. On the full scale the doors have a second hinge so when on the ground they don't hit when open. Well T-1 copied this perfectly and its the same way. Very cool looking.
Another thing on this bird is its all hidden linkages! No servos hanging out on this bird. So far most of the orders have all been plug and plays and that really is a good value for all the servos that get installed in this bird. I am waiting on a new air valve that we will be selling soon that can control up I think 7 functions. This I hope will help save channels.
The vertical stabs only have one small screw to keep them on and they have a direct drive servo linkage. That means the tail comes off very easy for transport. Only have to remove the formation light wire because the servo is installed in the fuselage.
A big challenge so far that I can see is going to be channels.... With slats flaps ailerons dual rudders flying stabs she is going to eat channels up. I only have 18 so I will find a way to make it all work.
This is my old yellow F22. The paint will look similar to this. Metallic camo paint is always fun to work with
After I get the pipe I will try and see what burner lights I can install.
#14
Thread Starter
My Feedback: (9)
This picture shows the serial number Raptor I am doing. T-1 was able to put a slight gold tint on the canopy already that looks great.
This plane can also be equipped with drop tanks. The tanks look pretty good and I plan on flying with them at times just to be different.
This plane can also be equipped with drop tanks. The tanks look pretty good and I plan on flying with them at times just to be different.
#15
I recall this is the thread where the fascination started, it's been a while.
http://www.rcuniverse.com/forum/rc-j...f22-build.html
http://www.rcuniverse.com/forum/rc-j...f22-build.html
#16
You can find all the technical data and ordering info at www.pacificrcjets.com . Like Kris had mentioned, this F-22 is a pre production model. The production models will have the panel lines reduced to .5 mm from the surface.
Dirk