RCU Forums
0 2018/07/03 20:56:55
0 2018/07/03 20:57:48
0 2018/07/04 11:07:56
0 2018/07/04 11:23:40
0 2018/07/30 17:13:47
0 2018/08/27 18:13:55
0 2018/09/03 12:43:41
0 2018/09/03 12:43:41
0 2018/09/03 12:54:00
Picture shows how leading edge fillet flairs smoothly into fuse sides in a way that drawing does not.
Picture shows how leading edge fillet flairs smoothly into fuse sides in a way that drawing does not.
0 2018/09/29 09:20:49
First block, hollowed (sanded) to fit fin.
First block, hollowed (sanded) to fit fin.
0 2018/09/29 09:20:58
0 2018/09/29 09:21:07
Sanding second block to fit fuse.
Sanding second block to fit fuse.
0 2018/09/29 09:21:10
After lots of sanding, starting to shape up. Will fill with epoxy/microballoons to smooth out edges.
After lots of sanding, starting to shape up. Will fill with epoxy/microballoons to smooth out edges.
0 2018/09/29 09:21:11
Used razor planer to remove most of the excess.
Used razor planer to remove most of the excess.
0 2018/09/29 09:26:39
0 2018/09/29 09:41:35
Starting to carve/sand out exhaust detents
Starting to carve/sand out exhaust detents
0 2018/10/19 16:49:10
Fuse 'flair' into fin
Fuse 'flair' into fin
0 2018/10/19 16:50:33
0 2018/10/21 09:45:15
0 2018/10/21 10:33:11
0 2018/10/21 10:33:13
0 2018/10/21 10:34:37
0 2018/12/02 15:17:29
0 2018/12/02 15:33:00
0 2018/12/16 11:39:06
0 2018/12/18 17:28:32
0 2018/12/18 17:28:34
0 2018/12/18 17:49:52
0 2018/12/18 17:50:05
0 2018/12/18 17:51:31
0 2018/12/18 17:52:56
0 2019/02/01 18:46:49
0 2019/06/29 10:31:25
0 2019/06/29 10:31:25
Interior former pressed in place, with some stand-offs that I made
Interior former pressed in place, with some stand-offs that I made
0 2019/07/07 15:24:39
Taped in place. Unfortunately, this identified more work for me, as the center engine open for this cowling is a bit higher than the one I used for mounting the engine. The engine will need to move up a bit. Well, I'll at least get more ground clearance for the prop!
Taped in place. Unfortunately, this identified more work for me, as the center engine open for this cowling is a bit higher than the one I used for mounting the engine. The engine will need to move up a bit. Well, I'll at least get more ground clearance for the prop!
0 2019/07/07 15:24:42
Interior former taped to firewall, highlighting shape differences.
Interior former taped to firewall, highlighting shape differences.
0 2019/07/07 15:24:42
Stand-offs drilled, dowel plugs fitted end epoxied to the former. Next step, epoxy the former into the cowling
Stand-offs drilled, dowel plugs fitted end epoxied to the former. Next step, epoxy the former into the cowling
0 2019/07/07 15:24:43
0 2019/11/30 19:10:54
0 2019/11/30 19:10:55
Advertising | Cookie Policy | Privacy Statement | Terms of Service | Manage Preferences Your Privacy Choices
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.